This is the small metal clip that goes around the leaves of a leaf spring, usually about 1/4 of the way down the length of spring. They are intended to keep your leaves in-line and to keep them from spreading too far away from the main leaf in the event...

Leaf spring wear pads go into small holes near the end of individual leaves to prevent leaf dig-in wear and noise caused by metal on metal friction during spring flex. Specifications: 2.5" x 2.5" Square Surface 5/8"L x 3/8"H x 3/8"T Peg What's In The Box: 1 Pad included (multiples...

Leaf Spring Clip wear pads go inside the clips on GM/Chevy trucks to prevent leaf dig-in wear and noise causes my metal on metal friction during spring flex. These are OE Spec and are meant to replace the original pads in the original style clips. For use with 2-1/2" wide...

Leaf spring friction pads go into small holes near the end of individual leaves to prevent leaf dig-in wear and noise caused by metal on metal friction during spring flex. Specifications: MGM7 - Surface diameter of 2 1/8" with a 3/8" peg MGM5 - Surface diameter of 2 7/16" with a...

OEM # 14022597 / 6270217 This part fits the following make/models: 1967 and up Chevy/GMC trucks with 2-1/2" wide leaf springs using 9/16 bolt holes. This is a rear leaf spring shackle. This is built from the primary OE Spec design, so it is the best adopted design from all the...

This part fits the following make/models: 1992 - 1996 G30/3500 Chassis Motorhomes (both eyes of the rear spring) G1500 G2500 and G3500 Savanna and Express vans 2004 - Current Colorado and Canyon (both eyes on the rear springs) 1992 - 2000 Blazer, Jimmy, Tahoe, Yukon, Denali, and Escalade (both eyes on the...

Part Number	Location on Vehicle	Spring Capacity	Number of Leaves
22-797HD	Rear	3,300lbs	7/1

*1999 and Up Chevy/GMC Silverado/Sierra Trucks require front eyebolt adaptor kit In order to use this spring This is an upgrade for the stock springs on any model of Chevy/GM Pickup. It was designed more for extra heavy applications on the 3500 1 ton models, but it can be used...

This part fits the following make/models: 1988 - 2007 1/2 Chevy Silverado 1500 1988 - 2007 1/2 GMC Sierra 1500 1988 - 2010 Chevy 2500/2500HD 1988 - 2010 GMC 2500/2500HD 1988 - 2010 Chevy 3500/3500HD 1988 - 2010 GMC 3500/3500HD 1992 - 1999 Chevy/GMC Suburban 1500 1992 - 1999 Chevy/GMC Suburban...

This part fits the following make/models: 1999 - 2017 Chevy Silverado 1500 and GMC Sierra 1500 (Front eyes of the rear spring) 1999 - 2010 Chevy Silverado 2500/2500HD and GMC Sierra 2500/2500HD (front eyes of the rear spring) 1999 - 2010 Chevy Silverado 3500/3500HD and GMC Sierra 3500/3500HD (front eyes of...

Leaf spring axle seats are weld on replacements for original axle seats or for custom axle applications 2.5" wide For use with 3" axle tube diameter Made from High Grade OE Spec Steel What's In The Box: 2x Axle Seats

Part Number	Location on Vehicle	Spring Capacity	Number of Leaves
22-1269	Rear	2,025 lbs	4/1

OEM # 15711753

This is a pair of cast steel leaf spring blocks. They can be used to raise or lower a vehicles height depending on the particular vehicles axle to spring set up. They have a standard pinion angle built in to help reduce the chance of needing to use shims. These...

These eye bolt adaptors convert 16mm to 9/16" allowing you to use rear leaf springs from the previous generation (1988-1998) Chevy/GMC pickups (1/2 ton 3/4 ton and 1 ton) on the newer generation trucks which come with lighter capacity leaf springs and are typically a lot more expensive. It's a...

Part Number	Location on Vehicle	Spring Capacity	Number of Leaves
22-1289	Rear	2,235lbs	5/1

Part Number	Location on Vehicle	Spring Capacity	Number of Leaves
22-1289HD	Rear	3,200lbs	5/1

New U-Bolt Body & Tie-Down Plate   Specifications: Made from Steel Overall Length - 6" Thickness - 1/2" Width - 1-1/2" Hole Diameter - 5/8" Hole Spacing (Between Holes) - 3-9/16" Hole Spacing (Center to Center) - 4-1/4"   What's In The Box: 1 Plate

Part Number	Location on Vehicle	Spring Capacity	Number of Leaves
22-1269HD	Rear	3,300lbs	7/1

This is an upgrade for the stock springs on any model of Silverado/Sierra. It was designed more for extra heavy applications on the 3500 1 ton models, but it can be used on lighter versions as well. This spring is NOT recommended for the 1500 model. It will fit but...

New U-Bolt Body & Tie-Down Plate   Specifications: Made from Steel Overall Length - 5-1/2" Thickness - 1/2" Width - 1-1/2" Hole Diameter - 5/8" Hole Spacing (Between Holes) - 3-1/16" Hole Spacing (Center to Center) - 3-3/4"   What's In The Box: 1 Plate

Part Number	Location on Vehicle	Spring Capacity	Number of Leaves
22-1269-T	Rear	2,025 lbs	4/1

OEM # 15711753

Part Number	Location on Vehicle	Spring Capacity	Number of Leaves
22-801	Rear	575lbs	1

This is a helper main leaf for the stock main leaf.

New U-Bolt Body & Tie-Down Plate   Specifications: Made from Steel Overall Length - 6-1/2" Thickness - 1/2" Width - 1-1/2" Hole Diameter - 5/8" Hole Spacing (Between Holes) - 4-1/16" Hole Spacing (Center to Center) - 4-3/4"   What's In The Box: 1 Plate