This is the small metal clip that goes around the leaves of a leaf spring, usually about 1/4 of the way down the length of spring. They are intended to keep your leaves in-line and to keep them from spreading too far away from the main leaf in the event...

Leaf spring wear pads go into small holes near the end of individual leaves to prevent leaf dig-in wear and noise caused by metal on metal friction during spring flex. Specifications: 2.5" x 2.5" Square Surface 5/8"L x 3/8"H x 3/8"T Peg What's In The Box: 1 Pad included (multiples...

Leaf Spring Clip wear pads go inside the clips on GM/Chevy trucks to prevent leaf dig-in wear and noise causes my metal on metal friction during spring flex. These are OE Spec and are meant to replace the original pads in the original style clips. For use with 2-1/2" wide...

Leaf spring friction pads go into small holes near the end of individual leaves to prevent leaf dig-in wear and noise caused by metal on metal friction during spring flex. Specifications: MGM7 - Surface diameter of 2 1/8" with a 3/8" peg MGM5 - Surface diameter of 2 7/16" with a...

This set will be: 9/16" Diameter Rod x 2 3/4" Wide Round Bend x 6 1/2" Legs Grade 5 Hardened Rolled National Fine Threads  Including High Nuts and Extra Thick U-bolt rated Washers Product Description:This is a BRAND NEW set of Grade 5 Hardened U-bolts. These are the real thing,...

Leaf spring axle seats are weld on replacements for original axle seats or for custom axle applications 2.5" wide For use with 3" axle tube diameter Made from High Grade OE Spec Steel What's In The Box: 2x Axle Seats

This is a pair of cast steel leaf spring blocks. They can be used to raise or lower a vehicles height depending on the particular vehicles axle to spring set up. They have a standard pinion angle built in to help reduce the chance of needing to use shims. These...

Part Number	Location on Vehicle	Spring Capacity	Number of Leaves
22-687	Rear	1,350lbs	3/1

This is a direct heavy duty replacement for the OEM factory spring. NOTE: This is NOT the correct spring for 1995 and up Blazer, Jimmy and Bravada or the High Rider ZR2 or ZR9 models.

Part Number	Location on Vehicle	Spring Capacity	Number of Leaves
22-687HD	Rear	1,750lbs	4/1

This is a Heavy Duty upgrade for the OEM factory spring. NOTE: This is NOT the correct spring for 1995 and up Blazer, Jimmy and Bravada or the High Rider ZR2 or ZR9 models.

New U-Bolt Body & Tie-Down Plate   Specifications: Made from Steel Overall Length - 6" Thickness - 1/2" Width - 1-1/2" Hole Diameter - 5/8" Hole Spacing (Between Holes) - 3-9/16" Hole Spacing (Center to Center) - 4-1/4"   What's In The Box: 1 Plate

This part fits the following make/models: 1982 - 2004 S10/S15 Pickup 1991 - 1994 Bravada 1983 - 1994 Blazer and Jimmy This is a BRAND NEW rear leaf spring shackle for GM S-truck Models. It is genuine stamped steel and built to original OE specs (not cheap cut and folded flat stock like...

New U-Bolt Body & Tie-Down Plate   Specifications: Made from Steel Overall Length - 5-1/2" Thickness - 1/2" Width - 1-1/2" Hole Diameter - 5/8" Hole Spacing (Between Holes) - 3-1/16" Hole Spacing (Center to Center) - 3-3/4"   What's In The Box: 1 Plate

New U-Bolt Body & Tie-Down Plate   Specifications: Made from Steel Overall Length - 6-1/2" Thickness - 1/2" Width - 1-1/2" Hole Diameter - 5/8" Hole Spacing (Between Holes) - 4-1/16" Hole Spacing (Center to Center) - 4-3/4"   What's In The Box: 1 Plate