This is the small metal clip that goes around the leaves of a leaf spring, usually about 1/4 of the way down the length of spring. They are intended to keep your leaves in-line and to keep them from spreading too far away from the main leaf in the event...

Leaf spring wear pads go into small holes near the end of individual leaves to prevent leaf dig-in wear and noise caused by metal on metal friction during spring flex. Specifications: 2.5" x 2.5" Square Surface 5/8"L x 3/8"H x 3/8"T Peg What's In The Box: 1 Pad included (multiples...

This is a U-bolt top cap/plate for Chevy and GM trucks with 2-1/2" wide rear springs. This plate is used on just about every GM truck and van that uses square shaped U-bolts. This part fits the following make/models: 1969 - 1994 K5 Blazer 1988 - 1998 Chevy and GMC 1500...

Leaf Spring Clip wear pads go inside the clips on GM/Chevy trucks to prevent leaf dig-in wear and noise causes my metal on metal friction during spring flex. These are OE Spec and are meant to replace the original pads in the original style clips. For use with 2-1/2" wide...

Leaf spring friction pads go into small holes near the end of individual leaves to prevent leaf dig-in wear and noise caused by metal on metal friction during spring flex. Specifications: MGM7 - Surface diameter of 2 1/8" with a 3/8" peg MGM5 - Surface diameter of 2 7/16" with a...

OEM # 14022597 / 6270217 This part fits the following make/models: 1967 and up Chevy/GMC trucks with 2-1/2" wide leaf springs using 9/16 bolt holes. This is a rear leaf spring shackle. This is built from the primary OE Spec design, so it is the best adopted design from all the...

Part Number	Location on Vehicle	Spring Capacity	Number of Leaves
22-797HD	Rear	3,300lbs	7/1

*1999 and Up Chevy/GMC Silverado/Sierra Trucks require front eyebolt adaptor kit In order to use this spring This is an upgrade for the stock springs on any model of Chevy/GM Pickup. It was designed more for extra heavy applications on the 3500 1 ton models, but it can be used...

This part fits the following make/models: 1988 - 2007 1/2 Chevy Silverado 1500 1988 - 2007 1/2 GMC Sierra 1500 1988 - 2010 Chevy 2500/2500HD 1988 - 2010 GMC 2500/2500HD 1988 - 2010 Chevy 3500/3500HD 1988 - 2010 GMC 3500/3500HD 1992 - 1999 Chevy/GMC Suburban 1500 1992 - 1999 Chevy/GMC Suburban...

Leaf spring axle seats are weld on replacements for original axle seats or for custom axle applications 2.5" wide For use with 3" axle tube diameter Made from High Grade OE Spec Steel What's In The Box: 2x Axle Seats

This is a pair of cast steel leaf spring blocks. They can be used to raise or lower a vehicles height depending on the particular vehicles axle to spring set up. They have a standard pinion angle built in to help reduce the chance of needing to use shims. These...

Part Number	Location on Vehicle	Spring Capacity	Number of Leaves
22-795-1	Rear	N/A	1

Part Number	Location on Vehicle	Spring Capacity	Number of Leaves
22-797	Rear	2,235lbs	5/1

*1999 to current Chevy/GMC 1500 1/2 ton pickup truck. (requires front eyebolt adaptor set This is a direct replacement for the stock springs on the 1988 through 2000 1 ton truck. 7 leaf versions are also available for heavy duty needs and will fit 1/2ton 3/4ton and 1ton pickups. 

New U-Bolt Body & Tie-Down Plate   Specifications: Made from Steel Overall Length - 6" Thickness - 1/2" Width - 1-1/2" Hole Diameter - 5/8" Hole Spacing (Between Holes) - 3-9/16" Hole Spacing (Center to Center) - 4-1/4"   What's In The Box: 1 Plate

This is a rear leaf spring shackle for Chevy/GMC 1 ton and P series trucks with 2-1/2" wide leaf springs and 9/16 eye bolts. Its an aftermarket build and very heavy duty. Includes hardware What's In The Box: 1 Shackle

New U-Bolt Body & Tie-Down Plate   Specifications: Made from Steel Overall Length - 5-1/2" Thickness - 1/2" Width - 1-1/2" Hole Diameter - 5/8" Hole Spacing (Between Holes) - 3-1/16" Hole Spacing (Center to Center) - 3-3/4"   What's In The Box: 1 Plate

This part fits the following make/models: 1988 - 1998 Chevy/GMC 1500 Pickup 1988 - 1998 Chevy/GMC 2500 Pickup 1988 - 1998 Chevy/GMC 3500 Pickup (does NOT include models with dual rear wheels) OE Spec Solution Heavy Build Heavy Duty. Includes hardware What's In The Box: 1 Hanger 1 eyebolt 4 mounting...

Product Information: 1988 - 1998 Chevy/GMC 4wd 1500 Pickup 1988 - 1998 Chevy/GMC 4wd 2500 Pickup 1988 - 1998 Chevy/GMC 4wd 3500 Pickup What's In The Box: 1 Bracket

New U-Bolt Body & Tie-Down Plate   Specifications: Made from Steel Overall Length - 6-1/2" Thickness - 1/2" Width - 1-1/2" Hole Diameter - 5/8" Hole Spacing (Between Holes) - 4-1/16" Hole Spacing (Center to Center) - 4-3/4"   What's In The Box: 1 Plate