This is the small metal clip that goes around the leaves of a leaf spring, usually about 1/4 of the way down the length of spring. They are intended to keep your leaves in-line and to keep them from spreading too far away from the main leaf in the event...

Leaf spring wear pads go into small holes near the end of individual leaves to prevent leaf dig-in wear and noise caused by metal on metal friction during spring flex. Specifications: 2.5" x 2.5" Square Surface 5/8"L x 3/8"H x 3/8"T Peg What's In The Box: 1 Pad included (multiples...

Leaf Spring Clip wear pads go inside the clips on GM/Chevy trucks to prevent leaf dig-in wear and noise causes my metal on metal friction during spring flex. These are OE Spec and are meant to replace the original pads in the original style clips. For use with 2-1/2" wide...

Leaf spring friction pads go into small holes near the end of individual leaves to prevent leaf dig-in wear and noise caused by metal on metal friction during spring flex. Specifications: MGM7 - Surface diameter of 2 1/8" with a 3/8" peg MGM5 - Surface diameter of 2 7/16" with a...

OEM # 14022597 / 6270217 This part fits the following make/models: 1967 and up Chevy/GMC trucks with 2-1/2" wide leaf springs using 9/16 bolt holes. This is a rear leaf spring shackle. This is built from the primary OE Spec design, so it is the best adopted design from all the...

This part fits the following make/models: 1988 - Current Silverado and Sierra 1500 & 1500HD - w/3.5" axle tube diameter 1988 - 2010 Silverado and Sierra 2500 & 2500HD - w/3.5" axle tube diameter 1992 - 1999 Suburban 1500 - w/3.5" axle tube diameter 1992 - 1999 Suburban 2500 - w/3.5"...

This part fits the following make/models: 1992 - 1999 Chevy Tahoe 1992 - 1999 GMC Yukon 1988 - 1992 Chevy Full Size Blazer 1999 - 2000 GMC Denali 1998 - 2000 Cadillac Escalade 1992 - 1999 Suburban This is a leaf spring hanger for the rear end of the rear leaf...

Leaf spring axle seats are weld on replacements for original axle seats or for custom axle applications 2.5" wide For use with 3" axle tube diameter Made from High Grade OE Spec Steel What's In The Box: 2x Axle Seats

This is a pair of cast steel leaf spring blocks. They can be used to raise or lower a vehicles height depending on the particular vehicles axle to spring set up. They have a standard pinion angle built in to help reduce the chance of needing to use shims. These...

New U-Bolt Body & Tie-Down Plate   Specifications: Made from Steel Overall Length - 6" Thickness - 1/2" Width - 1-1/2" Hole Diameter - 5/8" Hole Spacing (Between Holes) - 3-9/16" Hole Spacing (Center to Center) - 4-1/4"   What's In The Box: 1 Plate

This part fits the following make/models: 1992 - 1999 Chevy Tahoe 1992 - 1999 GMC Yukon 1988 - 1992 Chevy Full Size Blazer 1999 - 2000 GMC Denali 1998 - 2000 Cadillac Escalade 1992 - 1999 Suburban This is a leaf spring hanger for the rear end of the rear leaf...

New U-Bolt Body & Tie-Down Plate   Specifications: Made from Steel Overall Length - 5-1/2" Thickness - 1/2" Width - 1-1/2" Hole Diameter - 5/8" Hole Spacing (Between Holes) - 3-1/16" Hole Spacing (Center to Center) - 3-3/4"   What's In The Box: 1 Plate

Part Number	Location on Vehicle	Spring Capacity	Number of Leaves
22-907	Rear	2,760lbs	6

Part Number	Location on Vehicle	Spring Capacity	Number of Leaves
22-905	Rear	2,200lbs	5

Part Number	Location on Vehicle	Spring Capacity	Number of Leaves
22-1209HD	Rear	4,600lbs	10

Part Number	Location on Vehicle	Spring Capacity	Number of Leaves
22-1209	Rear	3,710lbs	9

Part Number	Location on Vehicle	Spring Capacity	Number of Leaves
22-1175	Rear	3,710lbs	3

New U-Bolt Body & Tie-Down Plate   Specifications: Made from Steel Overall Length - 6-1/2" Thickness - 1/2" Width - 1-1/2" Hole Diameter - 5/8" Hole Spacing (Between Holes) - 4-1/16" Hole Spacing (Center to Center) - 4-3/4"   What's In The Box: 1 Plate