Search By Vehicle Make/Model
Leaf Spring Clip Straps (1 3/4" - 2" - 2 1/4" - 2 1/2" - 3")
This is the small metal clip that goes around the leaves of a leaf spring, usually about 1/4 of the way down the length of spring. They are intended to keep your leaves in-line and to keep them from spreading too far away from the main leaf in the event...
Leaf Spring End Tip Wear Pads Anti Squeak Insert
Leaf spring wear pads go into small holes near the end of individual leaves to prevent leaf dig-in wear and noise caused by metal on metal friction during spring flex. Specifications: 2.5" x 2.5" Square Surface 5/8"L x 3/8"H x 3/8"T Peg What's In The Box: 1 Pad included (multiples...
Chevy GMC - U Bolt Top Cap Plate
This is a U-bolt top cap/plate for Chevy and GM trucks with 2-1/2" wide rear springs. This plate is used on just about every GM truck and van that uses square shaped U-bolts. This part fits the following make/models: 1969 - 1994 K5 Blazer 1988 - 1998 Chevy and GMC 1500...
Leaf Spring Clip Wear Pads Anti Squeak Insert
Leaf Spring Clip wear pads go inside the clips on GM/Chevy trucks to prevent leaf dig-in wear and noise causes my metal on metal friction during spring flex. These are OE Spec and are meant to replace the original pads in the original style clips. For use with 2-1/2" wide...
Leaf Spring Wear Pads Anti Squeak Inserts
Leaf spring friction pads go into small holes near the end of individual leaves to prevent leaf dig-in wear and noise caused by metal on metal friction during spring flex. Specifications: MGM7 - Surface diameter of 2 1/8" with a 3/8" peg MGM5 - Surface diameter of 2 7/16" with a...
Chevy GMC - Trucks - Rear Leaf Spring Shackle
OEM # 14022597 / 6270217 This part fits the following make/models: 1967 and up Chevy/GMC trucks with 2-1/2" wide leaf springs using 9/16 bolt holes. This is a rear leaf spring shackle. This is built from the primary OE Spec design, so it is the best adopted design from all the...
Leaf Spring Axle Seat Perch Mount (Pair)
Leaf spring axle seats are weld on replacements for original axle seats or for custom axle applications 2.5" wide For use with 3" axle tube diameter Made from High Grade OE Spec Steel What's In The Box: 2x Axle Seats
Leaf Spring Lift or Lowering Blocks (1.5" - 2" - 4" - 5.5")
This is a pair of cast steel leaf spring blocks. They can be used to raise or lower a vehicles height depending on the particular vehicles axle to spring set up. They have a standard pinion angle built in to help reduce the chance of needing to use shims. These...
Chevy GMC - Tahoe/Yukon/Escalade/Jimmy/Blazer - Leaf Spring (Rear, 5 Leaves)
| Part Number | Location on Vehicle | Spring Capacity | Number of Leaves |
|---|---|---|---|
| 22-909 | Rear | 1,750lbs | 4/1 |
U Bolt Body Tie Plate for 3-1/2"
New U-Bolt Body & Tie-Down Plate Specifications: Made from Steel Overall Length - 6" Thickness - 1/2" Width - 1-1/2" Hole Diameter - 5/8" Hole Spacing (Between Holes) - 3-9/16" Hole Spacing (Center to Center) - 4-1/4" What's In The Box: 1 Plate
U Bolt Body Tie Plate for 3"
New U-Bolt Body & Tie-Down Plate Specifications: Made from Steel Overall Length - 5-1/2" Thickness - 1/2" Width - 1-1/2" Hole Diameter - 5/8" Hole Spacing (Between Holes) - 3-1/16" Hole Spacing (Center to Center) - 3-3/4" What's In The Box: 1 Plate
U Bolt Body Tie Plate for 4"
New U-Bolt Body & Tie-Down Plate Specifications: Made from Steel Overall Length - 6-1/2" Thickness - 1/2" Width - 1-1/2" Hole Diameter - 5/8" Hole Spacing (Between Holes) - 4-1/16" Hole Spacing (Center to Center) - 4-3/4" What's In The Box: 1 Plate