This is the small metal clip that goes around the leaves of a leaf spring, usually about 1/4 of the way down the length of spring. They are intended to keep your leaves in-line and to keep them from spreading too far away from the main leaf in the event...

Leaf spring wear pads go into small holes near the end of individual leaves to prevent leaf dig-in wear and noise caused by metal on metal friction during spring flex. Specifications: 2.5" x 2.5" Square Surface 5/8"L x 3/8"H x 3/8"T Peg What's In The Box: 1 Pad included (multiples...

This is a U-bolt top cap/plate for Chevy and GM trucks with 2-1/2" wide rear springs. This plate is used on just about every GM truck and van that uses square shaped U-bolts. This part fits the following make/models: 1969 - 1994 K5 Blazer 1988 - 1998 Chevy and GMC 1500...

Leaf Spring Clip wear pads go inside the clips on GM/Chevy trucks to prevent leaf dig-in wear and noise causes my metal on metal friction during spring flex. These are OE Spec and are meant to replace the original pads in the original style clips. For use with 2-1/2" wide...

Leaf spring friction pads go into small holes near the end of individual leaves to prevent leaf dig-in wear and noise caused by metal on metal friction during spring flex. Specifications: MGM7 - Surface diameter of 2 1/8" with a 3/8" peg MGM5 - Surface diameter of 2 7/16" with a...

Leaf spring axle seats are weld on replacements for original axle seats or for custom axle applications 2.5" wide For use with 3" axle tube diameter Made from High Grade OE Spec Steel What's In The Box: 2x Axle Seats

This is a pair of cast steel leaf spring blocks. They can be used to raise or lower a vehicles height depending on the particular vehicles axle to spring set up. They have a standard pinion angle built in to help reduce the chance of needing to use shims. These...

Part Number	Location on Vehicle	Spring Capacity	Number of Leaves
22-403	Rear	2,350lbs	6

New U-Bolt Body & Tie-Down Plate   Specifications: Made from Steel Overall Length - 6" Thickness - 1/2" Width - 1-1/2" Hole Diameter - 5/8" Hole Spacing (Between Holes) - 3-9/16" Hole Spacing (Center to Center) - 4-1/4"   What's In The Box: 1 Plate

This is a rear leaf spring shackle for Chevy/GMC 1 ton and P series trucks with 2-1/2" wide leaf springs and 9/16 eye bolts. Its an aftermarket build and very heavy duty. Includes hardware What's In The Box: 1 Shackle

New U-Bolt Body & Tie-Down Plate   Specifications: Made from Steel Overall Length - 5-1/2" Thickness - 1/2" Width - 1-1/2" Hole Diameter - 5/8" Hole Spacing (Between Holes) - 3-1/16" Hole Spacing (Center to Center) - 3-3/4"   What's In The Box: 1 Plate

Part Number	Location on Vehicle	Spring Capacity	Number of Leaves
22-419	Rear	3,390lbs	7

*This spring was not originally offered and is an upgrade for the Colorado and Canyon.The centerbolt on the Colorado and Canyon is originally 5/16 and installing this spring will require modification to the centerbolt head or axle seat hole as it comes with a 3/8 centerbolt.

Part Number	Location on Vehicle	Spring Capacity	Number of Leaves
22-403-1	Rear	N/A	1

Part Number	Location on Vehicle	Spring Capacity	Number of Leaves
22-442	Front	2,190lbs	8/1

Part Number	Location on Vehicle	Spring Capacity	Number of Leaves
22-499	Rear	3,390lbs	8

*This spring was not originally offered and is an upgrade for the Colorado and Canyon. The centerbolt on the Colorado and Canyon is originally 5/16 and installing this spring will require modification to the centerbolt head or axle seat hole as it comes with a 3/8 centerbolt.

This is a front leaf spring shackle made for use with 5/8 eyebolts. Its an aftermarket build and very heavy duty. What's In The Box: 1 Shackle

New U-Bolt Body & Tie-Down Plate   Specifications: Made from Steel Overall Length - 6-1/2" Thickness - 1/2" Width - 1-1/2" Hole Diameter - 5/8" Hole Spacing (Between Holes) - 4-1/16" Hole Spacing (Center to Center) - 4-3/4"   What's In The Box: 1 Plate