This is the small metal clip that goes around the leaves of a leaf spring, usually about 1/4 of the way down the length of spring. They are intended to keep your leaves in-line and to keep them from spreading too far away from the main leaf in the event...

Leaf spring wear pads go into small holes near the end of individual leaves to prevent leaf dig-in wear and noise caused by metal on metal friction during spring flex. Specifications: 2.5" x 2.5" Square Surface 5/8"L x 3/8"H x 3/8"T Peg What's In The Box: 1 Pad included (multiples...

Leaf Spring Clip wear pads go inside the clips on GM/Chevy trucks to prevent leaf dig-in wear and noise causes my metal on metal friction during spring flex. These are OE Spec and are meant to replace the original pads in the original style clips. For use with 2-1/2" wide...

Leaf spring friction pads go into small holes near the end of individual leaves to prevent leaf dig-in wear and noise caused by metal on metal friction during spring flex. Specifications: MGM7 - Surface diameter of 2 1/8" with a 3/8" peg MGM5 - Surface diameter of 2 7/16" with a...

Product Description: This is a brand new U-bolt bottom plate for 1 ton trucks from 1973 to 1987 with 3.5" axles. It's made from cast steel and is very heavy duty. Vehicle Applications: 1973 - 1987 Chevrolet/GMC C30 & K30 What's In The Box: 1 Bottom Plate

OEM # 14022597 / 6270217 This part fits the following make/models: 1967 and up Chevy/GMC trucks with 2-1/2" wide leaf springs using 9/16 bolt holes. This is a rear leaf spring shackle. This is built from the primary OE Spec design, so it is the best adopted design from all the...

Part Number	Location on Vehicle	Spring Capacity	Number of Leaves
22-547	Rear	2,600lbs	8/1

Leaf spring axle seats are weld on replacements for original axle seats or for custom axle applications 2.5" wide For use with 3" axle tube diameter Made from High Grade OE Spec Steel What's In The Box: 2x Axle Seats

This is a pair of cast steel leaf spring blocks. They can be used to raise or lower a vehicles height depending on the particular vehicles axle to spring set up. They have a standard pinion angle built in to help reduce the chance of needing to use shims. These...

This is a brand new U-bolt top cap/plate for 1 ton (will work on 1/2 ton and 3/4 as well) GM Trucks with square bend U-bolts and 2-1/2 inch wide springs (typically ranging from 1985 - current). Its made from cast steel and is very heavy duty. What's In The Box:...

Part Number	Location on Vehicle	Spring Capacity	Number of Leaves
22-403	Rear	2,350lbs	6

New U-Bolt Body & Tie-Down Plate   Specifications: Made from Steel Overall Length - 6" Thickness - 1/2" Width - 1-1/2" Hole Diameter - 5/8" Hole Spacing (Between Holes) - 3-9/16" Hole Spacing (Center to Center) - 4-1/4"   What's In The Box: 1 Plate

Part Number	Location on Vehicle	Spring Capacity	Number of Leaves
22-617	Rear	3,995lbs	10

New U-Bolt Body & Tie-Down Plate   Specifications: Made from Steel Overall Length - 5-1/2" Thickness - 1/2" Width - 1-1/2" Hole Diameter - 5/8" Hole Spacing (Between Holes) - 3-1/16" Hole Spacing (Center to Center) - 3-3/4"   What's In The Box: 1 Plate

Part Number	Location on Vehicle	Spring Capacity	Number of Leaves
43-1855	Rear	2,700lbs	2/1

Part Number	Location on Vehicle	Spring Capacity	Number of Leaves
22-547HD	Rear	3,500lbs	8/1

Part Number	Location on Vehicle	Spring Capacity	Number of Leaves
22-403-1	Rear	N/A	1

Part Number	Location on Vehicle	Spring Capacity	Number of Leaves
22-503	Rear	1,950lbs	8

New U-Bolt Body & Tie-Down Plate   Specifications: Made from Steel Overall Length - 6-1/2" Thickness - 1/2" Width - 1-1/2" Hole Diameter - 5/8" Hole Spacing (Between Holes) - 4-1/16" Hole Spacing (Center to Center) - 4-3/4"   What's In The Box: 1 Plate