This is the small metal clip that goes around the leaves of a leaf spring, usually about 1/4 of the way down the length of spring. They are intended to keep your leaves in-line and to keep them from spreading too far away from the main leaf in the event...

Leaf spring wear pads go into small holes near the end of individual leaves to prevent leaf dig-in wear and noise caused by metal on metal friction during spring flex. Specifications: 2.5" x 2.5" Square Surface 5/8"L x 3/8"H x 3/8"T Peg What's In The Box: 1 Pad included (multiples...

This is a U-bolt top cap/plate for Chevy and GM trucks with 2-1/2" wide rear springs. This plate is used on just about every GM truck and van that uses square shaped U-bolts. This part fits the following make/models: 1969 - 1994 K5 Blazer 1988 - 1998 Chevy and GMC 1500...

Leaf Spring Clip wear pads go inside the clips on GM/Chevy trucks to prevent leaf dig-in wear and noise causes my metal on metal friction during spring flex. These are OE Spec and are meant to replace the original pads in the original style clips. For use with 2-1/2" wide...

Actual bolt may be plated or non-plated Other sizes are available What's In The Box: 1 bolt 1 nut *Finish may vary

This set will be: 9/16" Diameter Rod x 2 1/2" Wide Square Bend Grade 5 Hardened Rolled National Fine Threads  Including High Nuts and Extra Thick U-bolt rated Washers Product Description:This is a BRAND NEW set of Grade 5 hardened U-bolts. These are the real thing, NOT the the low...

Leaf spring friction pads go into small holes near the end of individual leaves to prevent leaf dig-in wear and noise caused by metal on metal friction during spring flex. Specifications: MGM7 - Surface diameter of 2 1/8" with a 3/8" peg MGM5 - Surface diameter of 2 7/16" with a...

This is a 5/16 x 5" Center Bolt for a leaf spring. It has threads most of the way down and extra length can be cut off after the nut has been tightened. Other sizes are available as well. *BE ADVISED - Leaf Spring Center Bolts are NOT hardened and...

Product Description: This is a brand new U-bolt bottom plate for 1 ton trucks from 1973 to 1987 with 3.5" axles. It's made from cast steel and is very heavy duty. Vehicle Applications: 1973 - 1987 Chevrolet/GMC C30 & K30 What's In The Box: 1 Bottom Plate

OEM # 14022597 / 6270217 This part fits the following make/models: 1967 and up Chevy/GMC trucks with 2-1/2" wide leaf springs using 9/16 bolt holes. This is a rear leaf spring shackle. This is built from the primary OE Spec design, so it is the best adopted design from all the...

Custom U-bolts made to your specifications. Product Description: This is a BRAND NEW set of Grade 8 hardened U-bolts. These are the real thing, NOT the the low grade, under sized "universal" U-bolts that you usually get with most lift kits and aftermarket bolt-ons. We custom make all of our U-bolts using the highest grade...

Custom U-bolts made to your specifications. Product Description: This is a BRAND NEW set of Grade 5 hardened U-bolts. These are the real thing, NOT the the low grade, under sized "universal" U-bolts that you usually get with most lift kits and aftermarket bolt-ons. We custom make all of our U-bolts using the highest...

This set will be: 9/16" Diameter Rod x 2 3/4" Wide Round Bend x 6 1/2" Legs Grade 5 Hardened Rolled National Fine Threads  Including High Nuts and Extra Thick U-bolt rated Washers Product Description:This is a BRAND NEW set of Grade 5 Hardened U-bolts. These are the real thing,...

OEM #  6272088 This part fits the following make/models: 1973 - 1987 Chevy/GMC K10 K20 K30 Series Trucks This is a front leaf spring Shackle, bushing and bolt kit (rear of front spring) for: *This kit does one spring on one side of the truck *Includes hardware What's In The Box:...

This part fits the following make/models: 1999 - 2008 Ford F250/F350/F450/F550 Superduty and Excursion This eyebolt measures 18mm x 150mm, comes complete with the nut and is designed specifically for this front eye application. Changing the front springs on these trucks almost always requires cutting the old eyebolt out because the factory...

OEM #  3C3Z5798AA / 3C3Z-5798-AA / F81Z5798AA / F81Z-5798-AA Product Description: Brand New Heavy Duty version of the OE spec U-bolt plate for vehicles using either the 3.5" or 4" axle tube diameter Fits: 1999 - 2010 - F-250 Superduty 1999 - 2010 - F-350 Superduty 2000 - 2006 - Excursion  What's In...

This part fits the following make/models: 1988 - 2007 1/2 Chevy Silverado 1500 1988 - 2007 1/2 GMC Sierra 1500 1988 - 2010 Chevy 2500/2500HD 1988 - 2010 GMC 2500/2500HD 1988 - 2010 Chevy 3500/3500HD 1988 - 2010 GMC 3500/3500HD 1992 - 1999 Chevy/GMC Suburban 1500 1992 - 1999 Chevy/GMC Suburban...

This part fits the following make/models: 1988 - Current Silverado and Sierra 1500 & 1500HD - w/3.5" axle tube diameter 1988 - 2010 Silverado and Sierra 2500 & 2500HD - w/3.5" axle tube diameter 1992 - 1999 Suburban 1500 - w/3.5" axle tube diameter 1992 - 1999 Suburban 2500 - w/3.5"...

This part fits the following make/models: 1992 - 1996 G30/3500 Chassis Motorhomes (both eyes of the rear spring) G1500 G2500 and G3500 Savanna and Express vans 2004 - Current Colorado and Canyon (both eyes on the rear springs) 1992 - 2000 Blazer, Jimmy, Tahoe, Yukon, Denali, and Escalade (both eyes on the...

This part fits the following make/models: 1992 - 1999 Chevy Tahoe 1992 - 1999 GMC Yukon 1988 - 1992 Chevy Full Size Blazer 1999 - 2000 GMC Denali 1998 - 2000 Cadillac Escalade 1992 - 1999 Suburban This is a leaf spring hanger for the rear end of the rear leaf...

Product Description: This is a replacement leaf spring eye bolt with nut. Its a grade 10.9 hardened steel bolt that typically fits many standard truck and van springs. 14mm O.D. 100mm Long Actual bolt may be plated or non-plated What's In The Box: 1 bolt 1 nut We do combine...

This part fits the following make/models: 1999 - 2017 Chevy Silverado 1500 and GMC Sierra 1500 (Front eyes of the rear spring) 1999 - 2010 Chevy Silverado 2500/2500HD and GMC Sierra 2500/2500HD (front eyes of the rear spring) 1999 - 2010 Chevy Silverado 3500/3500HD and GMC Sierra 3500/3500HD (front eyes of...

OEM # 1C3Z5776BA / 3C3C5776AB / 3C3Z5776AB / F81Z5776CA This part fits the following make/models: 1999 - 2010 Ford SuperDuty trucks using 16mm rear eyebolts This is a BRAND NEW Rear Leaf spring Shackle for 1999 - 2010 Ford superduty trucks using 16mm rear eyebolts. This is NOT a Dorman part. This is made by...

Custom U-bolts made to your specifications. Product Description: This is a BRAND NEW set of Grade 5 hardened U-bolts. These are the real thing, NOT the the low grade, under sized "universal" U-bolts that you usually get with most lift kits and aftermarket bolt-ons. We custom make all of our U-bolts using the highest...

Custom U-bolts made to your specifications. Product Description: This is a BRAND NEW set of Grade 8 hardened U-bolts. These are the real thing, NOT the the low grade, under sized "universal" U-bolts that you usually get with most lift kits and aftermarket bolt-ons. We custom make all of our U-bolts using the highest grade...

Leaf spring axle seats are weld on replacements for original axle seats or for custom axle applications 2.5" wide For use with 3" axle tube diameter Made from High Grade OE Spec Steel What's In The Box: 2x Axle Seats

This is a pair of cast steel leaf spring blocks. They can be used to raise or lower a vehicles height depending on the particular vehicles axle to spring set up. They have a standard pinion angle built in to help reduce the chance of needing to use shims. These...

OEM # E6TZ5776A / E6TZ5776B / ZZM027144 This part fits the following make/models: 1980 - 1996 F-150 2wd w/ 2 1/2 inch wide springs 1997 - 2004 F-150 2wd & 4wd 1997 - 1998 F250XL Variant w/2 1/2" wide springs 2004 F-150 Heritage w/2 1/2" wide springs 1983 - 2010 Ranger & Mazda B Pickups...

This part fits the following make/models: 1967 - 1981 Chevy Camaro 1968 - 1981 Chevy Nova 1967 - 1981 Pontiac Firebird This is a T Bolt set for the Axle Spring Plate/Seat of the rear leaf springs on Camaro Firebird and Nova. They are 7/16 diameter and 1-3/4" long. It's an...

Custom U-bolts made to your specifications. Product Description: This is a BRAND NEW set of Grade 8 hardened U-bolts. These are the real thing, NOT the the low grade, under sized "universal" U-bolts that you usually get with most lift kits and aftermarket bolt-ons. We custom make all of our U-bolts using the highest grade...

These eye bolt adaptors convert 16mm to 9/16" allowing you to use rear leaf springs from the previous generation (1988-1998) Chevy/GMC pickups (1/2 ton 3/4 ton and 1 ton) on the newer generation trucks which come with lighter capacity leaf springs and are typically a lot more expensive. It's a...

This is a brand new U-bolt top cap/plate for 1 ton (will work on 1/2 ton and 3/4 as well) GM Trucks with square bend U-bolts and 2-1/2 inch wide springs (typically ranging from 1985 - current). Its made from cast steel and is very heavy duty. What's In The Box:...

OEM # ZZM027144 / E0TZ5776A / E2TZ5776A / EOTZ5776A This part fits the following make/models: 1980 - 1996 F150 4wd only 1980 - 1997 F250 2wd & 4wd* 1980 - 1997 F350 2wd & 4wd *Does NOT fit the 1997/1998 F-250 Variant with 2-1/2" wide springs This is a BRAND NEW rear leaf spring shackle...

This part fits the following make/models: 1991 - 2000 Chevy/GMC C3500HD Medium Duty Chassis Truck with 16mm eyebolts This is a BRAND NEW Rear Leaf spring Shackle for 91 - 00 Chevy/GMC C3500HD Medium Duty Chassis Truck with 16mm eyebolts. Its an aftermarket build and very heavy duty. What's In The...

Custom U-bolts made to your specifications. Product Description: This is a BRAND NEW set of Grade 5 hardened U-bolts. These are the real thing, NOT the the low grade, under sized "universal" U-bolts that you usually get with most lift kits and aftermarket bolt-ons. We custom make all of our U-bolts using the highest...

This part fits the following make/models: 1999 - 2010 Ford SuperDuty trucks using 16mm rear eyebolts. This is NOT a Dorman part, this is made by an actual SRI OE Spec manufacturer, so it is heavier and stronger than the OEM ford part or any inferior reproduction, which means you dont...

This part fits the following make/models: 1980 - 1997 F350 1980 - 1997 F250 1980 - 1996/97 Carryover F150 4WD w/ 3" wide springs ONLY 1992 - 2003 Ford E250/E350 Vans w/3" wide springs *Does NOT fit the 1997/1998 F-250 LightWeight Variant or F350 Dually with 2-1/4" wide rear springs *Includes...

This part fits the following make/models: 1980 - 1996 Ford F150 4wd trucks w/ 3" wide springs This is a BRAND NEW Leaf spring Hanger for the front end of the rear leaf spring on 1980 - 1996 Ford F150 4wd trucks with 3" wide springs. This is NOT a Dorman part....

This part fits the following make/models: 1987 - 1998 Ford F250 or F350 trucks with 3" wide springs This is a BRAND NEW 6 Hole Leaf spring Hanger for the front end of the rear leaf spring on 1987 - 1998 Ford F250 or F350 trucks with 3" wide springs. This...

This part fits the following make/models: 2002 - 2008 Dodge Ram 1500 It's a replacement for the original OEM parts and has the same specifications to the original. What's In The Box: 1 Shackle

This part fits the following make/models: 1999 - 2010 F-250 Superduty w/ 3.5" axle tube diameter 2000 - 2006 Excursion 2009 - 2013 E-250 2009 - 2013 E-350 w/ 3.5" axle tube diameter Heavy Duty version of the OE spec U-bolt plate for vehicles with 3.5" axle tube diameters What's In...

This part fits the following make/models: 1982 - 2004 S10/S15 Pickup 1991 - 1994 Bravada 1983 - 1994 Blazer and Jimmy This is a BRAND NEW rear leaf spring shackle for GM S-truck Models. It is genuine stamped steel and built to original OE specs (not cheap cut and folded flat stock like...

New U-Bolt Body & Tie-Down Plate   Specifications: Made from Steel Overall Length - 6" Thickness - 1/2" Width - 1-1/2" Hole Diameter - 5/8" Hole Spacing (Between Holes) - 3-9/16" Hole Spacing (Center to Center) - 4-1/4"   What's In The Box: 1 Plate

Interchanges with Part # OEM - 355420 Automann - MIH55205 What's In The Box: 1 Rubber Bump Stop (for one side of the truck)

Custom U-bolts made to your specifications. Product Description: This is a BRAND NEW set of Grade 5 hardened U-bolts. These are the real thing, NOT the the low grade, under sized "universal" U-bolts that you usually get with most lift kits and aftermarket bolt-ons. We custom make all of our U-bolts using the highest...

This part fits the following make/models: 1992 - 1999 Chevy Tahoe 1992 - 1999 GMC Yukon 1988 - 1992 Chevy Full Size Blazer 1999 - 2000 GMC Denali 1998 - 2000 Cadillac Escalade 1992 - 1999 Suburban This is a leaf spring hanger for the rear end of the rear leaf...

This part fits the following make/models: 1999 - 2004 Dodge Dakota 1998 - 2003 Dodge Durango This is an OEM replacement rubber encased leaf spring bushing for the rear leaf springs on Dodge Trucks. This bushing is used in several other leaf spring applications. You should always measure your spring eye...

This part fits the following make/models: 1983 - 2003 Ranger 1994 - 1997 Mazda B Series Pickup This is NOT a Dorman part. This is made by an actual SRI OE Spec manufacturer, so it is heavier and stronger than the OEM ford part or any inferior reproduction, which means you...

This part fits the following make/models: 1992 - 2006 E-150 (rear eye of rear spring on) 1986 - 1990 Bronco II (rear eye of rear spring on) 1991 - 2002 Explorer/Mountaineer (rear eye of rear spring)  1983 - 2003 Ranger and Mazda 100 pickups (rear eye of rear spring) 1980 - 1996...

Custom U-bolts made to your specifications. Product Description: This is a BRAND NEW set of Grade 8 hardened U-bolts. These are the real thing, NOT the the low grade, under sized "universal" U-bolts that you usually get with most lift kits and aftermarket bolt-ons. We custom make all of our U-bolts using the highest grade...